DIY kit assembly

Built a scanner? Started to build a scanner? Record your progress here. Doesn't need to be a whole scanner - triggers and other parts are fine. Commercial scanners are fine too.

Moderator: peterZ

thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

Rob:

Image

1. Is that a bolt or a screw? Which direction is it pointed?

2. Is this attached at all, or resting atop the frame?

3. Do you have a detailed photo of how the book holder attaches to the lift arm assembly?

Dan:

Good point. I'll see if they're open tomorrow and give it a shot. Most of town has been shut down today, we're in the midst of Snowpocalypse 2012.
thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

thinkJason wrote:Rob:
1. Is that a bolt or a screw? Which direction is it pointed?

2. Is this attached at all, or resting atop the frame?
Answered my own question, bolts for both.
goldo
Posts: 10
Joined: 01 Feb 2012, 04:43
E-book readers owned: sony
Number of books owned: 1000

Re: DIY kit assembly

Post by goldo »

where could i bought this kit ? and how much cost it ?

thank you.
thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

goldo wrote:where could i bought this kit ? and how much cost it ?

thank you.
See Rob's Makers meeting Buyers thread in Agora. I highly recommend Rob's work. You can also take the plans to a local CNC shop to have it cut.
thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

So I walked to the local framing shop, the owner charged me $2 to cut the 11x14" glass down to 11x13.75". I also borrowed a power drill from a friend, so I can get to drilling today once the battery charges up. Still have to wait on painting, there's two feet of snow outside. Progress is happening!
thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

Platen test fit, round two!

Looks good so far:

Image

My cat decided to check it out:

Image

There's a good chunk of space to fill in order to keep the glass stable (many suggestions have been proposed on the board thus far):

Image
Image

At 13.75" glass height, it spreads the frame apart very slightly (maybe bolting it together will hold the glass by pressure?):

Image

11" glass width fills the channel perfectly:

Image

Next step: drilling!
thinkJason
Posts: 35
Joined: 19 Jan 2012, 19:51
E-book readers owned: iPad
Number of books owned: 1000
Location: Denver, CO

Re: DIY kit assembly

Post by thinkJason »

Drilling is progressing quite nicely. Noticed a few things:

1. #8 wood screws don't have a wide enough head to attach bearings to the book holder:

Image

2. Are these two different orientations of the bike handle holder?

Image
Image
Image

Back to drilling! Here's the tools I used:

Image

The light fixture needs attachment:

Image

The front half of the frame needs screws on both sides, but is too thin to countersink (need rounded head screws):

Image

The front handle mechanism needs attachment also:

Image

After countersinking:

Image

More drilling on the way...
User avatar
rob
Posts: 773
Joined: 03 Jun 2009, 13:50
E-book readers owned: iRex iLiad, Kindle 2
Number of books owned: 4000
Country: United States
Location: Maryland, United States
Contact:

Re: DIY kit assembly

Post by rob »

thinkJason wrote:
thinkJason wrote:Rob:
1. Is that a bolt or a screw? Which direction is it pointed?

2. Is this attached at all, or resting atop the frame?
Answered my own question, bolts for both.
You can use bolts, but I think it is easier to use screws. My worry was that after unscrewing, turning the box upside down to paperback mode, screwing in again, unscrewing, turning the box right side up again for a hardback, and repeating over and over, eventually the screw won't hold, and I'd have to use a bolt anyway.

So you can choose bolt or screw.
The Singularity is Near. ~ http://halfbakedmaker.org ~ Follow me as I build the world's first all-mechanical steam-powered computer.
User avatar
rob
Posts: 773
Joined: 03 Jun 2009, 13:50
E-book readers owned: iRex iLiad, Kindle 2
Number of books owned: 4000
Country: United States
Location: Maryland, United States
Contact:

Re: DIY kit assembly

Post by rob »

Kitty! See, Dan? The Internet is made of cats.

Also, nice Allie Brosh homage :)
The Singularity is Near. ~ http://halfbakedmaker.org ~ Follow me as I build the world's first all-mechanical steam-powered computer.
User avatar
rob
Posts: 773
Joined: 03 Jun 2009, 13:50
E-book readers owned: iRex iLiad, Kindle 2
Number of books owned: 4000
Country: United States
Location: Maryland, United States
Contact:

Re: DIY kit assembly

Post by rob »

Thank you so much for posting your experiences. They will certainly help with the next revision!
thinkJason wrote:#8 wood screws don't have a wide enough head to attach bearings to the book holder.
Hmm, well, drywall screws worked for me. All of these worked for me (yes, that's a bag o' generic drywall screws, so old that I don't know what brand they'd be). I got the green box at the Despot.
IMG_0086.JPG
thinkJason wrote:Are these two different orientations of the bike handle holder?
Yes, you have a choice as to which one you want to use. Choose the one that is more comfortable for you. The smaller one is good for me.
thinkJason wrote:The front half of the frame needs screws on both sides, but is too thin to countersink
They can be, but you have to be careful to go just far enough in. If you don't want to take the chance, a round head is fine too.
The Singularity is Near. ~ http://halfbakedmaker.org ~ Follow me as I build the world's first all-mechanical steam-powered computer.
Post Reply